Well, since the crappo Chinese fan seized and the crook who sold it never sent me a replacement, I decided to do things my way.
Went to pick-a-part and picked up a radiator from an Alfa, transmission cooler from a BMW and a fan from a Mercedes.
The range of bits was for good reasons.
The radiator had to be a certain size. Well, it had to be about the same size as the Valiant one. The Alfa was perfect (really, almost exactly the same size) as well as being quite thin. I got the fan that was on it. All this for $103.50.
Transmission cooler was from a different wrecker: One near my dad's and they charged $36! Hell, that's expensive.
Can't remember what the merc fan cost (got it ages ago) but it wasn't very much (also from P.A.P.) - probably about $25.
OK, so radiator almost went straight in. Both hoses were on the driver's side like the Val, and I set it up so the bottom hose went into the new one. Got a couple of rubber blocks to set it on and found out that it also lined up nicely with two factory drilled holes in the bottom support panel! Just had to secure it at the top, but out it came and the trans cooler had to go in first. I'll get pics tomorrow. It's nearly finished now but I just haven't taken pictures yet.
The cooler had to be modified. I cut it off at the rubber hydraulic hoses and for the Val, I hack sawed the pipes back to the steel. When this had been done I thoroughly cleaned up the cut and the inside of the pipe. The adapters that go into the radiator fit into the end of the steel pipes like a glove, so I screwed them in. They were quite secure, but I unscrewed them, mixed up some industrial strength araldyte and spread liberally onto the threads before screwing back in. Left them for 24 hours to set before tightening.
So, cooler, radiator and original fan... No, the original fan is massively too wide. I tried to modify it to fit (it had a steel shroud damn it!) but no go. Mercedes fans are an amazing combination of heavy duty and efficient design. It was easily half the width of the Alfa fan, so on it went. This required a bit of stuffing around but I got there in the end. Radiator must not touch the fan housing or the transmission cooler. All of these things would rub holes in each other so make sure they don't touch.
OK, so the Alfa radiator has a thermostat, so I have to learn what sort of output it has and rig up a thermo switch to come on automatically, cool the car down and shut off. The temperature of activation must be higher than the temp of deactivation. If not, it would be coming on for a few seconds at a time every few seconds! Not what we want, so we have it come on around, say, 90 and switch off around 85. It'll have to heat back up to 90 until she kicks back in.
I'm currently researching this feature but there's plenty of information about cheap or free ways to accomplish it.
Also have to get the A/C to activate the fan, or even put in a second one. I did buy two so it's possible, but I'll see how she runs with only one. Thursday will be a good day to test it out, seeing as it's expected to be 40 in Melbourne!
Showing posts with label coolant. Show all posts
Showing posts with label coolant. Show all posts
Saturday, January 4, 2014
Monday, January 7, 2013
Hot weather and how to keep the old girl cool
When you have a classic car with A/C how do you keep it cool?
Here are some tips for keeping your car cool, from most easiest to less easiest ;-):
1. Clean your radiator, check your thermostat. I was amazed at how much rusty crap was blocking the radiator a few months ago. Clean it, as in take the radiator out of the car and tip it upside-down, hose it and buy some new concentrated anti-boil/anti-freeze. Also, very important to solder up any leaks or take it to get it fixed: Water leaks get worse due to the increase in pressure when it's hot. While you're at this, check your thermostat. If it works OK but your radiator isn't the best since they're all old and most have a few blockages, you can reduce the possibility of overheating by fitting a lower temperature thermostat. this makes the engine run slightly less efficiently, but I'd rather it use a little more fuel than break down at the first traffic jam. In Melbourne, very heavy traffic is a given and a nightmare for old cars.
2. Fit a better fan. The std fan for the Valiant 225 is a four blade. This is crap really, and at a recent (Bendigo, Nov 2012) swap meet I got a chromed hemi 6 bladed chromed fan (although the chrome has seen better days) for $10. This definitely made a big difference, but the car still overheats on really hot days (like last Saturday, 40°C). Bloody heavy fan but it pulls a lot more air through. It made a difference straight away, and the Val would definitely have failed on me before now if I hadn't done this.
3. Fit a shroud between the fan and the radiator, as close as possible to the fan. This forces more air to come from the front of the car into the radiator, rather than from around the engine bay. I modified a modern plastic one, pulled off a Volvo. Doesn't matter if you cut, glue, tape, screw etc. it together if you just want the effect.
4. Fit an electric fan. I bought one but haven't fitted it yet. It's the narrowest large diameter electric fan I could find ($60 ebay, sent from QLD) because the A/C compressor means there isn't much space. Electric fans have the advantage of efficiency: They don't operate when the water's cold and since it's not driven by the motor they don't take any effort to run (you get more horsepower and better fuel economy, and it gets better at higher engine speed like extractors). That said, they do require electricity, and when running, the alternator produces more drag on the engine. However, it's the best solution and the most difficult (I haven't done it yet). You'll need to completely remove the manual fan, of course, and possibly fit new screws (in case you need to put back the old fan which you should keep somewhere handy).
5. Check/renew your water pump. If your water pump is an older one or you have been a bit slack in putting the green inhibitor in the water it'll be corroded, and much less effective. It's easy to remove the pump and check this. If your pump is badly corroded, get a new one. I have a new one in the shed (hmm.. might start keeping it in the car - you never know) and they're not expensive or hard to find (auto surplus in Mitcham usually have them in stock, or even Repco). If your old one was corroded, you'll notice an immediate improvement.
Here are a few driving tips:
1. Is your car an automatic? If so, put it into neutral at the lights: Melbourne has the worst traffic and sitting at the lights is what overheats your car. Here's why: Your car idles slow in neutral, slower in drive, and it seems that although the faster idle creates more heat, the faster fan speed as well as the faster water pump more than makes up for this. I've tested it and in drive, my car overheats much faster than in neutral. If the traffic lights are known to take more than a minute to change, turn the engine off.
2. With aftermarket A/C you usually have a thermostat dial: When at the lights, turn it to warmer (less cold) and have the car in neutral. When not at the lights have it cooler.
The A/C heats your coolant up in two ways:
i. Dragging on the engine, slowing it down and creating more work for it.
ii. The condensor (at the front of the radiator) is the hot part of the heat exchanger, and heats up the air before it gets to the radiator (it sits in front of the radiator).
If your car is overheating, choose all or some of the following to slow or stop it (depending on the circumstances):
* Turn off the A/C.
* Stop the car. The water temperature will appear to go up rapidly when you do this and the radiator may blow out some water due to the pressure.
* Turn on the heater. This will provide additional cooling, albeit at the expense of comfort.
When you stop the car whilst overheating, it will probably blow some pressure in the form of water and/or steam. This is normal and nothing to worry about. If you're wanting to just put in some more water either wait for the engine to cool down (like, an hour) or throw a cloth over the radiator cap and remove it (note: It's really dangerous to remove the cap from a hot engine) then with the engine running pour in some water. If you don't have the engine running, the temperature difference once you start the engine may crack the block or head.
So to summarise:
* Flush your radiator by removing it
OK, that's Mike's tips for driving in the heat. I didn't drive the Val today: Took the missus' Verada instead (mmm... thermostatically controlled electric fan). Told you I hadn't installed the electric one yet: Might do so this week.
Mike
Here are some tips for keeping your car cool, from most easiest to less easiest ;-):
1. Clean your radiator, check your thermostat. I was amazed at how much rusty crap was blocking the radiator a few months ago. Clean it, as in take the radiator out of the car and tip it upside-down, hose it and buy some new concentrated anti-boil/anti-freeze. Also, very important to solder up any leaks or take it to get it fixed: Water leaks get worse due to the increase in pressure when it's hot. While you're at this, check your thermostat. If it works OK but your radiator isn't the best since they're all old and most have a few blockages, you can reduce the possibility of overheating by fitting a lower temperature thermostat. this makes the engine run slightly less efficiently, but I'd rather it use a little more fuel than break down at the first traffic jam. In Melbourne, very heavy traffic is a given and a nightmare for old cars.
2. Fit a better fan. The std fan for the Valiant 225 is a four blade. This is crap really, and at a recent (Bendigo, Nov 2012) swap meet I got a chromed hemi 6 bladed chromed fan (although the chrome has seen better days) for $10. This definitely made a big difference, but the car still overheats on really hot days (like last Saturday, 40°C). Bloody heavy fan but it pulls a lot more air through. It made a difference straight away, and the Val would definitely have failed on me before now if I hadn't done this.
3. Fit a shroud between the fan and the radiator, as close as possible to the fan. This forces more air to come from the front of the car into the radiator, rather than from around the engine bay. I modified a modern plastic one, pulled off a Volvo. Doesn't matter if you cut, glue, tape, screw etc. it together if you just want the effect.
4. Fit an electric fan. I bought one but haven't fitted it yet. It's the narrowest large diameter electric fan I could find ($60 ebay, sent from QLD) because the A/C compressor means there isn't much space. Electric fans have the advantage of efficiency: They don't operate when the water's cold and since it's not driven by the motor they don't take any effort to run (you get more horsepower and better fuel economy, and it gets better at higher engine speed like extractors). That said, they do require electricity, and when running, the alternator produces more drag on the engine. However, it's the best solution and the most difficult (I haven't done it yet). You'll need to completely remove the manual fan, of course, and possibly fit new screws (in case you need to put back the old fan which you should keep somewhere handy).
5. Check/renew your water pump. If your water pump is an older one or you have been a bit slack in putting the green inhibitor in the water it'll be corroded, and much less effective. It's easy to remove the pump and check this. If your pump is badly corroded, get a new one. I have a new one in the shed (hmm.. might start keeping it in the car - you never know) and they're not expensive or hard to find (auto surplus in Mitcham usually have them in stock, or even Repco). If your old one was corroded, you'll notice an immediate improvement.
Here are a few driving tips:
1. Is your car an automatic? If so, put it into neutral at the lights: Melbourne has the worst traffic and sitting at the lights is what overheats your car. Here's why: Your car idles slow in neutral, slower in drive, and it seems that although the faster idle creates more heat, the faster fan speed as well as the faster water pump more than makes up for this. I've tested it and in drive, my car overheats much faster than in neutral. If the traffic lights are known to take more than a minute to change, turn the engine off.
2. With aftermarket A/C you usually have a thermostat dial: When at the lights, turn it to warmer (less cold) and have the car in neutral. When not at the lights have it cooler.
The A/C heats your coolant up in two ways:
i. Dragging on the engine, slowing it down and creating more work for it.
ii. The condensor (at the front of the radiator) is the hot part of the heat exchanger, and heats up the air before it gets to the radiator (it sits in front of the radiator).
If your car is overheating, choose all or some of the following to slow or stop it (depending on the circumstances):
* Turn off the A/C.
* Stop the car. The water temperature will appear to go up rapidly when you do this and the radiator may blow out some water due to the pressure.
* Turn on the heater. This will provide additional cooling, albeit at the expense of comfort.
When you stop the car whilst overheating, it will probably blow some pressure in the form of water and/or steam. This is normal and nothing to worry about. If you're wanting to just put in some more water either wait for the engine to cool down (like, an hour) or throw a cloth over the radiator cap and remove it (note: It's really dangerous to remove the cap from a hot engine) then with the engine running pour in some water. If you don't have the engine running, the temperature difference once you start the engine may crack the block or head.
So to summarise:
* Flush your radiator by removing it
OK, that's Mike's tips for driving in the heat. I didn't drive the Val today: Took the missus' Verada instead (mmm... thermostatically controlled electric fan). Told you I hadn't installed the electric one yet: Might do so this week.
Mike
Sunday, November 7, 2010
A/C Compressor is in
Yes, it has a compressor! This is the most difficult part of the installation, and was accomplished by handing the tricky bit over to the professional.
The tricky bit is the bracket that holds both the compressor and the adjustment wheel. This was constructed by my local Valiant specialist (Brad at Val Wreck - 97209770). The bracket had to be manufactured because firstly there weren't a lot of slant sixes with A/C compressors (although Brad assures me there were a few VEs fitted with it) and secondly even if there were, they weren't fitted with my extractors, which could get in the way. Pictures will come later.
The bottom pulley used was taken from a hemi: The diameter is perfect but the holes don't match up, so he had to drill two new ones (I think the hemi has four, but the slant only has three). I also had to re-route the fuel line a bit, since the compressor would otherwise have squashed it. This is hopefully only temporary, though, as I intend to put multi point EFI on it when I get around to it.
The next thing on the to-do list is installing the new heater/evaporator. One change I have to make there is that since there is no control for where the air intake is sourced from, I have opted to take the easy road: I'll be blocking up the normal air intake from the plenum and have recycled air only. Making it source the air from the plenum is much harder, and switching from plenum to recycle is more difficult again. That's not to say it's not a possibility for the future: I'm a big fan of a quiet car, and everyone knows that when you switch to recycle you're turning up the noise by about 400%. I tried doing this job last week, but only then discovered how hard it was going to be to include the outside air and replaced the old core. When the old core comes out this time, it will stay out.
One little problem we had was that the fan was too close to the new compressor and would have smashed it to pieces if we'd started the engine with it in place. The fix was a combination of two actions:
1. We put a slightly longer spacer on the water pump. This gives the bonus effect of pulling more air through the radiator and thus making the cooling system more efficient.
2. Cut outs in the fan. We cut out "L" shaped pieces from the fan blades. This matched the original fans, so we didn't feel bad about it.
One other job from last weekend was that I reverse flushed the coolant. Due to several leaks and a broken radiator early this year I never got around to replacing the antifreeze. The result is very brown looking water, and rust isn't the sort of thing you want washing through your nice new system or causing your radiator to block. Cooling is extremely important with an A/C system because:
1. Your compressor is a drag on the motor and causes more heat to be generated.
2. Your condenser (the small radiator at the front of the water radiator) gets cooled first by the incoming air, leaving warmer than normal air for the water cooling.
3. You will be using your A/C mostly on hot days.
Brad said to try it out as-is and keep an eye on the temperature gauge. This is how I tend to do this sort of thing anyway. Obviously if the temperature rises too much I will tweak the system by, for example, adding a fan shroud, which improves the effectiveness of the cooling. It already has a cool thermostat so there's little to no danger of overheating during this testing.
The next option would be a seven bladed fan from a CL or CM. If it's still too hat we'll be looking at an electric thermo fan. Another bonus here would be that it is more efficient, since it doesn't come on at all until needed.
Well, that's all for now. Photos later.
The tricky bit is the bracket that holds both the compressor and the adjustment wheel. This was constructed by my local Valiant specialist (Brad at Val Wreck - 97209770). The bracket had to be manufactured because firstly there weren't a lot of slant sixes with A/C compressors (although Brad assures me there were a few VEs fitted with it) and secondly even if there were, they weren't fitted with my extractors, which could get in the way. Pictures will come later.
The bottom pulley used was taken from a hemi: The diameter is perfect but the holes don't match up, so he had to drill two new ones (I think the hemi has four, but the slant only has three). I also had to re-route the fuel line a bit, since the compressor would otherwise have squashed it. This is hopefully only temporary, though, as I intend to put multi point EFI on it when I get around to it.
The next thing on the to-do list is installing the new heater/evaporator. One change I have to make there is that since there is no control for where the air intake is sourced from, I have opted to take the easy road: I'll be blocking up the normal air intake from the plenum and have recycled air only. Making it source the air from the plenum is much harder, and switching from plenum to recycle is more difficult again. That's not to say it's not a possibility for the future: I'm a big fan of a quiet car, and everyone knows that when you switch to recycle you're turning up the noise by about 400%. I tried doing this job last week, but only then discovered how hard it was going to be to include the outside air and replaced the old core. When the old core comes out this time, it will stay out.
One little problem we had was that the fan was too close to the new compressor and would have smashed it to pieces if we'd started the engine with it in place. The fix was a combination of two actions:
1. We put a slightly longer spacer on the water pump. This gives the bonus effect of pulling more air through the radiator and thus making the cooling system more efficient.
2. Cut outs in the fan. We cut out "L" shaped pieces from the fan blades. This matched the original fans, so we didn't feel bad about it.
One other job from last weekend was that I reverse flushed the coolant. Due to several leaks and a broken radiator early this year I never got around to replacing the antifreeze. The result is very brown looking water, and rust isn't the sort of thing you want washing through your nice new system or causing your radiator to block. Cooling is extremely important with an A/C system because:
1. Your compressor is a drag on the motor and causes more heat to be generated.
2. Your condenser (the small radiator at the front of the water radiator) gets cooled first by the incoming air, leaving warmer than normal air for the water cooling.
3. You will be using your A/C mostly on hot days.
Brad said to try it out as-is and keep an eye on the temperature gauge. This is how I tend to do this sort of thing anyway. Obviously if the temperature rises too much I will tweak the system by, for example, adding a fan shroud, which improves the effectiveness of the cooling. It already has a cool thermostat so there's little to no danger of overheating during this testing.
The next option would be a seven bladed fan from a CL or CM. If it's still too hat we'll be looking at an electric thermo fan. Another bonus here would be that it is more efficient, since it doesn't come on at all until needed.
Well, that's all for now. Photos later.
Subscribe to:
Posts (Atom)