Well, since the crappo Chinese fan seized and the crook who sold it never sent me a replacement, I decided to do things my way.
Went to pick-a-part and picked up a radiator from an Alfa, transmission cooler from a BMW and a fan from a Mercedes.
The range of bits was for good reasons.
The radiator had to be a certain size. Well, it had to be about the same size as the Valiant one. The Alfa was perfect (really, almost exactly the same size) as well as being quite thin. I got the fan that was on it. All this for $103.50.
Transmission cooler was from a different wrecker: One near my dad's and they charged $36! Hell, that's expensive.
Can't remember what the merc fan cost (got it ages ago) but it wasn't very much (also from P.A.P.) - probably about $25.
OK, so radiator almost went straight in. Both hoses were on the driver's side like the Val, and I set it up so the bottom hose went into the new one. Got a couple of rubber blocks to set it on and found out that it also lined up nicely with two factory drilled holes in the bottom support panel! Just had to secure it at the top, but out it came and the trans cooler had to go in first. I'll get pics tomorrow. It's nearly finished now but I just haven't taken pictures yet.
The cooler had to be modified. I cut it off at the rubber hydraulic hoses and for the Val, I hack sawed the pipes back to the steel. When this had been done I thoroughly cleaned up the cut and the inside of the pipe. The adapters that go into the radiator fit into the end of the steel pipes like a glove, so I screwed them in. They were quite secure, but I unscrewed them, mixed up some industrial strength araldyte and spread liberally onto the threads before screwing back in. Left them for 24 hours to set before tightening.
So, cooler, radiator and original fan... No, the original fan is massively too wide. I tried to modify it to fit (it had a steel shroud damn it!) but no go. Mercedes fans are an amazing combination of heavy duty and efficient design. It was easily half the width of the Alfa fan, so on it went. This required a bit of stuffing around but I got there in the end. Radiator must not touch the fan housing or the transmission cooler. All of these things would rub holes in each other so make sure they don't touch.
OK, so the Alfa radiator has a thermostat, so I have to learn what sort of output it has and rig up a thermo switch to come on automatically, cool the car down and shut off. The temperature of activation must be higher than the temp of deactivation. If not, it would be coming on for a few seconds at a time every few seconds! Not what we want, so we have it come on around, say, 90 and switch off around 85. It'll have to heat back up to 90 until she kicks back in.
I'm currently researching this feature but there's plenty of information about cheap or free ways to accomplish it.
Also have to get the A/C to activate the fan, or even put in a second one. I did buy two so it's possible, but I'll see how she runs with only one. Thursday will be a good day to test it out, seeing as it's expected to be 40 in Melbourne!
Showing posts with label heat. Show all posts
Showing posts with label heat. Show all posts
Saturday, January 4, 2014
Saturday, March 9, 2013
Electric fan again
Well since it was about 35 yesterday, I decided to take the Valiant to pick the little one up from school. When it got to operating temperature, I just left the fan on. To further test it, I turned the air conditioning fan to full and the thermostat to the coldest setting. In stages of course since I didn't want the embarrassment of being stranded. It all worked really well, and I left the fan on a few minutes after stopping each time to prevent the usual heat build up, which all too often leads to an embarrassing blowing off of excess pressure (and water).
Also during Friday I visited the wrecker and got a nice looking volt meter from a Magna (well, it was probably put together in the same factory). Have to put it on yet, but it tested OK. Should then be able to tell if we ever get a case of over voltage or if the alternator just dies.
I also picked up a different thermostat: One I had a threaded nut for. Although I haven't faltered yet with turning the fan on and off, it'd be nice if it were taken care of automatically. This will be a job for next week.
Drive safely, preferably in an old Valiant, of course.
Also during Friday I visited the wrecker and got a nice looking volt meter from a Magna (well, it was probably put together in the same factory). Have to put it on yet, but it tested OK. Should then be able to tell if we ever get a case of over voltage or if the alternator just dies.
I also picked up a different thermostat: One I had a threaded nut for. Although I haven't faltered yet with turning the fan on and off, it'd be nice if it were taken care of automatically. This will be a job for next week.
Drive safely, preferably in an old Valiant, of course.
Thursday, October 14, 2010
Putting the EFI on hold for now
Here is the reason:
1. Mating the Ford item to the Holley slant six manifold was impossible (well, without a further $600 or so) and wouldn't have looked very good.
I have decided to go about it differently. The Ford already has an inlet manifold. Is it possible to modify this to go straight on to the slant? I believe it is, but since the inlet holes are spaced differently (ford holes are uniform, slant six holes are not) it would be no easy task. I want to cut the metal separating the Ford manifold and make an Aluminium mount that will bolt to the slant on one side and to the EFI manifold bit on the other. Either way it will almost certainly require a new fuel rail. I'm going to halt it for now, though.
2. It's getting warm in Melbourne.
The Val isn't the most inviting car in the Summer. Last Summer I painted the roof white (well, off-white) to cut down on roof heat which worked really well. Also tinted the windows, and in a large wagon that's not a trivial task. Finally, when the roof lining went on earlier this year, I had the upholsterer add some extra insulation.
After all that, I know it will still be unbearable when it gets over 30, so it's time to get the Ford's Air conditioning unit on and working.
In preparation, I bought (from ebay) a brand new after market heating and cooling unit for $255. This fits under the dash and in theory will attach to all existing heater outlets. This means you don't have a large and very obvious looking unit right there at your passenger's legs. It just replaces your original one and adds an evaporator and (hopefully) quieter fan. Haven't heard it yet, and have no idea how difficult it will be to fit.
Disadvantages include that I will be losing a face-level outlet. You can buy these but I chose the hidden option instead.
It will be a while before I can get around to fit it, but will keep you informed of course.
1. Mating the Ford item to the Holley slant six manifold was impossible (well, without a further $600 or so) and wouldn't have looked very good.
I have decided to go about it differently. The Ford already has an inlet manifold. Is it possible to modify this to go straight on to the slant? I believe it is, but since the inlet holes are spaced differently (ford holes are uniform, slant six holes are not) it would be no easy task. I want to cut the metal separating the Ford manifold and make an Aluminium mount that will bolt to the slant on one side and to the EFI manifold bit on the other. Either way it will almost certainly require a new fuel rail. I'm going to halt it for now, though.
2. It's getting warm in Melbourne.
The Val isn't the most inviting car in the Summer. Last Summer I painted the roof white (well, off-white) to cut down on roof heat which worked really well. Also tinted the windows, and in a large wagon that's not a trivial task. Finally, when the roof lining went on earlier this year, I had the upholsterer add some extra insulation.
After all that, I know it will still be unbearable when it gets over 30, so it's time to get the Ford's Air conditioning unit on and working.
In preparation, I bought (from ebay) a brand new after market heating and cooling unit for $255. This fits under the dash and in theory will attach to all existing heater outlets. This means you don't have a large and very obvious looking unit right there at your passenger's legs. It just replaces your original one and adds an evaporator and (hopefully) quieter fan. Haven't heard it yet, and have no idea how difficult it will be to fit.
Disadvantages include that I will be losing a face-level outlet. You can buy these but I chose the hidden option instead.
It will be a while before I can get around to fit it, but will keep you informed of course.
Subscribe to:
Posts (Atom)