Well, since the crappo Chinese fan seized and the crook who sold it never sent me a replacement, I decided to do things my way.
Went to pick-a-part and picked up a radiator from an Alfa, transmission cooler from a BMW and a fan from a Mercedes.
The range of bits was for good reasons.
The radiator had to be a certain size. Well, it had to be about the same size as the Valiant one. The Alfa was perfect (really, almost exactly the same size) as well as being quite thin. I got the fan that was on it. All this for $103.50.
Transmission cooler was from a different wrecker: One near my dad's and they charged $36! Hell, that's expensive.
Can't remember what the merc fan cost (got it ages ago) but it wasn't very much (also from P.A.P.) - probably about $25.
OK, so radiator almost went straight in. Both hoses were on the driver's side like the Val, and I set it up so the bottom hose went into the new one. Got a couple of rubber blocks to set it on and found out that it also lined up nicely with two factory drilled holes in the bottom support panel! Just had to secure it at the top, but out it came and the trans cooler had to go in first. I'll get pics tomorrow. It's nearly finished now but I just haven't taken pictures yet.
The cooler had to be modified. I cut it off at the rubber hydraulic hoses and for the Val, I hack sawed the pipes back to the steel. When this had been done I thoroughly cleaned up the cut and the inside of the pipe. The adapters that go into the radiator fit into the end of the steel pipes like a glove, so I screwed them in. They were quite secure, but I unscrewed them, mixed up some industrial strength araldyte and spread liberally onto the threads before screwing back in. Left them for 24 hours to set before tightening.
So, cooler, radiator and original fan... No, the original fan is massively too wide. I tried to modify it to fit (it had a steel shroud damn it!) but no go. Mercedes fans are an amazing combination of heavy duty and efficient design. It was easily half the width of the Alfa fan, so on it went. This required a bit of stuffing around but I got there in the end. Radiator must not touch the fan housing or the transmission cooler. All of these things would rub holes in each other so make sure they don't touch.
OK, so the Alfa radiator has a thermostat, so I have to learn what sort of output it has and rig up a thermo switch to come on automatically, cool the car down and shut off. The temperature of activation must be higher than the temp of deactivation. If not, it would be coming on for a few seconds at a time every few seconds! Not what we want, so we have it come on around, say, 90 and switch off around 85. It'll have to heat back up to 90 until she kicks back in.
I'm currently researching this feature but there's plenty of information about cheap or free ways to accomplish it.
Also have to get the A/C to activate the fan, or even put in a second one. I did buy two so it's possible, but I'll see how she runs with only one. Thursday will be a good day to test it out, seeing as it's expected to be 40 in Melbourne!
Showing posts with label Car. Show all posts
Showing posts with label Car. Show all posts
Saturday, January 4, 2014
Tuesday, September 28, 2010
Welcome to my new blog
Valcook is a pseudomyn mainly because my top interests at the moment at cooking and ... my Valiant! The Val was in very poor condition when I got it. Spent a fortune on it and now it's a daily driver, quite comfortable and has central locking and a car alarm, which I fitted. Someone else fitted the extractors, which massively increased the efficiency - much better power and fuel economy.
This space will include things I have done to my car and things I intend to do, as they happen.
At the moment I'm a bit obsessed with efficiency and the carburettor doesn't work very well. On LPG it takes a full ten seconds to start the engine! Once started it will run brilliantly on LPG, but it uses almost twice the fuel it did when running well on petrol. What could I possibly do? Well, tried putting a kit through the carby but this did nothing more than cost me money. The fact is that it is almost certainly wear in the throttle body causing the drama. Haven't mentioned the drama? Sorry...
The drama: It doesn't start at all on petrol usually. If it does, it runs like crap until warm, then still exhibits a massive flat spot at the start of acceleration. So, there's a pretty major problem running either fuel, AND I don't know how efficiently the thing is running.
The Solution: So how about EFI? I've been doing a bit (a lot) of reading about it and it seems that the whole thing can be accomplished using an old Ford EEC-IV coupled to an Aussiespeed four barrel EFI slant six manifold (don't laugh, they really exist). I'll have to at least heavily modify the fuel rail or even make a new one. I get the manifold ($435 from a 1987 ZL Fairlane) tomorrow and the rest on Sat morning from a wrecker (he said $250 for the whole lot). So, is it worth $685? We will see. I'll take a lot of photos and put them up as the project goes. Also decided to have a go at putting an oxygen sensor into the exhaust to help tune it. These sound like a fantastic diagnostic tool and I happen to have one sitting in the shed. Advantages of EFI I'm keen on are:
1. Easier to start the car
2. Tunable fuel system
3. Better Fuel economy (it's a 3.7L slant six).
4. More power
5. Less pollution. OK, I don't care much about this, but it is a side-effect nonetheless.
Reliability was going to be in there too, but I can't imagine the Val being more reliable than it is.
More after I get the manifold.
This space will include things I have done to my car and things I intend to do, as they happen.
At the moment I'm a bit obsessed with efficiency and the carburettor doesn't work very well. On LPG it takes a full ten seconds to start the engine! Once started it will run brilliantly on LPG, but it uses almost twice the fuel it did when running well on petrol. What could I possibly do? Well, tried putting a kit through the carby but this did nothing more than cost me money. The fact is that it is almost certainly wear in the throttle body causing the drama. Haven't mentioned the drama? Sorry...
The drama: It doesn't start at all on petrol usually. If it does, it runs like crap until warm, then still exhibits a massive flat spot at the start of acceleration. So, there's a pretty major problem running either fuel, AND I don't know how efficiently the thing is running.
The Solution: So how about EFI? I've been doing a bit (a lot) of reading about it and it seems that the whole thing can be accomplished using an old Ford EEC-IV coupled to an Aussiespeed four barrel EFI slant six manifold (don't laugh, they really exist). I'll have to at least heavily modify the fuel rail or even make a new one. I get the manifold ($435 from a 1987 ZL Fairlane) tomorrow and the rest on Sat morning from a wrecker (he said $250 for the whole lot). So, is it worth $685? We will see. I'll take a lot of photos and put them up as the project goes. Also decided to have a go at putting an oxygen sensor into the exhaust to help tune it. These sound like a fantastic diagnostic tool and I happen to have one sitting in the shed. Advantages of EFI I'm keen on are:
1. Easier to start the car
2. Tunable fuel system
3. Better Fuel economy (it's a 3.7L slant six).
4. More power
5. Less pollution. OK, I don't care much about this, but it is a side-effect nonetheless.
Reliability was going to be in there too, but I can't imagine the Val being more reliable than it is.
More after I get the manifold.
Subscribe to:
Posts (Atom)