Showing posts with label fan. Show all posts
Showing posts with label fan. Show all posts

Saturday, January 4, 2014

Another Summer and more cooling problems

Well, since the crappo Chinese fan seized and the crook who sold it never sent me a replacement, I decided to do things my way.
Went to pick-a-part and picked up a radiator from an Alfa, transmission cooler from a BMW and a fan from a Mercedes.
The range of bits was for good reasons.
The radiator had to be a certain size. Well, it had to be about the same size as the Valiant one. The Alfa was perfect (really, almost exactly the same size) as well as being quite thin. I got the fan that was on it. All this for $103.50.
Transmission cooler was from a different wrecker: One near my dad's and they charged $36! Hell, that's expensive.
Can't remember what the merc fan cost (got it ages ago) but it wasn't very much (also from P.A.P.) - probably about $25.
OK, so radiator almost went straight in. Both hoses were on the driver's side like the Val, and I set it up so the bottom hose went into the new one. Got a couple of rubber blocks to set it on and found out that it also lined up nicely with two factory drilled holes in the bottom support panel! Just had to secure it at the top, but out it came and the trans cooler had to go in first. I'll get pics tomorrow. It's nearly finished now but I just haven't taken pictures yet.
The cooler had to be modified. I cut it off at the rubber hydraulic hoses and for the Val, I hack sawed the pipes back to the steel. When this had been done I thoroughly cleaned up the cut and the inside of the pipe. The adapters that go into the radiator fit into the end of the steel pipes like a glove, so I screwed them in. They were quite secure, but I unscrewed them, mixed up some industrial strength araldyte and spread liberally onto the threads before screwing back in. Left them for 24 hours to set before tightening.
So, cooler, radiator and original fan... No, the original fan is massively too wide. I tried to modify it to fit (it had a steel shroud damn it!) but no go. Mercedes fans are an amazing combination of heavy duty and efficient design. It was easily half the width of the Alfa fan, so on it went. This required a bit of stuffing around but I got there  in the end. Radiator must not touch the fan housing or the transmission cooler. All of these things would rub holes in each other so make sure they don't touch.
OK, so the Alfa radiator has a thermostat, so I have to learn what sort of output it has and rig up a thermo switch to come on automatically, cool the car down and shut off. The temperature of activation must be higher than the temp of deactivation. If not, it would be coming on for a few seconds at a time every few seconds! Not what we want, so we have it come on around, say, 90 and switch off around 85. It'll have to heat back up to 90 until she kicks back in.
I'm currently researching this feature but there's plenty of information about cheap or free ways to accomplish it.
Also have to get the A/C to activate the fan, or even put in a second one. I did buy two so it's possible, but I'll see how she runs with only one. Thursday will be a good day to test it out, seeing as it's expected to be 40 in Melbourne!

Sunday, May 19, 2013

The Electric Fan part 3

The two thermo switches I got from the wrecker were rendered useless: I heated one of them with a blow torch (then discovering they're very sensitive) and dropped the other on the concrete floor, breaking it instantly.
So, what to do when the world seems to be letting you know it doesn't want you to is to stop trying to do it. I fitted a nicer switch on the inside of the car and made it slightly more secure (but still hanging down from the dash). Since it's Winter now, I rarely have to even switch it on, provided I avoid heavy traffic (*very* difficult in Melbourne these days).
Found out the following about how it heats up:
1. Putting the car into neutral when coasting downwards (don't speed, though) is great for reducing the coolant temperature.
2. Putting the car into neutral at red lights no longer has any cooling effect, since the fan is now gone, so doing it is now a no-no.
3. Provided I never forget to look at the gauge every minute or so, the car will always operate at the right temperature.
4. Rain doesn't necessarily cool it better.
5. Cold air does. Driving through the mountains saw the temperature gauge drop quite a bit.
6. Travelling at 60-70KM/H is good for cooling, 80 is OK, but 100 will heat the coolant. The engine has to work proportionally harder at 100 to overcome the additional air resistance and produces much more heat, whereas at lower speeds the wind blowing through the radiator is more cooling than what the engine produces.

The car seems to use less fuel, and (this could be imagination, but) it also seems more responsive.

Thanks for reading.

Saturday, March 9, 2013

Electric fan again

Well since it was about 35 yesterday, I decided to take the Valiant to pick the little one up from school. When it got to operating temperature, I just left the fan on. To further test it, I turned the air conditioning fan to full and the thermostat to the coldest setting. In stages of course since I didn't want the embarrassment of being stranded. It all worked really well, and I left the fan on a few minutes after stopping each time to prevent the usual heat build up, which all too often leads to an embarrassing blowing off of excess pressure (and water).
Also during Friday I visited the wrecker and got a nice looking volt meter from a Magna (well, it was probably put together in the same factory). Have to put it on yet, but it tested OK. Should then be able to tell if we ever get a case of over voltage or if the alternator just dies.

I also picked up a different thermostat: One I had a threaded nut for. Although I haven't faltered yet with turning the fan on and off, it'd be nice if it were taken care of automatically. This will be a job for next week.

Drive safely, preferably in an old Valiant, of course.

Monday, March 4, 2013

A few improvements

OK, last weekend was a big one for the Valiant. Several improvements made, and the car is better by far.

Electric fan

Pulled out the heavy one and put the electric fan in. Took ages (about 6 hours) and had to be offset, due to the water pump being in the way. Had to put another relay in since the fan draws a few amps. Did this first, and the ammeter went nuts every time I turned the fan on.

Bypassing the firewall plug

I did the improvement mentioned last post. A simple wire to connect the alternator with the starter relay. Now of course the ammeter doesn't work (sits at zero). I have to look out for a volt meter to replace it or turn the ammeter into a volt meter. I'm thinking the second option is preferred. It's more difficult since the thing will have to be calibrated but considering over-voltage killed my last battery it's essential to get one soon.


Linking the central locking to the alarm


Luckily (or it may be normal) the alarm has the ability to activate the central locking. Mine pulses a 400mA signal. The only way to get it working is to use two standard (bosch type) relays.
Here is how a relay is wired (taken from http://www.pbase.com/image/35092434.jpg):

The activation signal is (in my case) wired with a 12V wire at the other end. Activation signal from alarm to 87, battery to 30. This will allow the other two terminals to bridge. Other terminals are 86 to earth (a good one) and 87 to the central locking's "lock all" signal wire.
Do the same with the unlock.

Next plans

Put a relay in the headlight circuit, a bigger alternator and electronic regulator.

Sunday, November 7, 2010

A/C Compressor is in

Yes, it has a compressor! This is the most difficult part of the installation, and was accomplished by handing the tricky bit over to the professional.
The tricky bit is the bracket that holds both the compressor and the adjustment wheel. This was constructed by my local Valiant specialist (Brad at Val Wreck - 97209770). The bracket had to be manufactured because firstly there weren't a lot of slant sixes with A/C compressors (although Brad assures me there were a few VEs fitted with it) and secondly even if there were, they weren't fitted with my extractors, which could get in the way. Pictures will come later.
The bottom pulley used was taken from a hemi: The diameter is perfect but the holes don't match up, so he had to drill two new ones (I think the hemi has four, but the slant only has three). I also had to re-route the fuel line a bit, since the compressor would otherwise have squashed it. This is hopefully only temporary, though, as I intend to put multi point EFI on it when I get around to it.
The next thing on the to-do list is installing the new heater/evaporator. One change I have to make there is that since there is no control for where the air intake is sourced from, I have opted to take the easy road: I'll be blocking up the normal air intake from the plenum and have recycled air only. Making it source the air from the plenum is much harder, and switching from plenum to recycle is more difficult again. That's not to say it's not a possibility for the future: I'm a big fan of a quiet car, and everyone knows that when you switch to recycle you're turning up the noise by about 400%. I tried doing this job last week, but only then discovered how hard it was going to be to include the outside air and replaced the old core. When the old core comes out this time, it will stay out.
One little problem we had was that the fan was too close to the new compressor and would have smashed it to pieces if we'd started the engine with it in place. The fix was a combination of two actions:
1. We put a slightly longer spacer on the water pump. This gives the bonus effect of pulling more air through the radiator and thus making the cooling system more efficient.
2. Cut outs in the fan. We cut out "L" shaped pieces from the fan blades. This matched the original fans, so we didn't feel bad about it.

One other job from last weekend was that I reverse flushed the coolant. Due to several leaks and a broken radiator early this year I never got around to replacing the antifreeze. The result is very brown looking water, and rust isn't the sort of thing you want washing through your nice new system or causing your radiator to block. Cooling is extremely important with an A/C system because:
1. Your compressor is a drag on the motor and causes more heat to be generated.
2. Your condenser (the small radiator at the front of the water radiator) gets cooled first by the incoming air, leaving warmer than normal air for the water cooling.
3. You will be using your A/C mostly on hot days.
Brad said to try it out as-is and keep an eye on the temperature gauge. This is how I tend to do this sort of thing anyway. Obviously if the temperature rises too much I will tweak the system by, for example, adding a fan shroud, which improves the effectiveness of the cooling. It already has a cool thermostat so there's little to no danger of overheating during this testing.
The next option would be a seven bladed fan from a CL or CM. If it's still too hat we'll be looking at an electric thermo fan. Another bonus here would be that it is more efficient, since it doesn't come on at all until needed.
Well, that's all for now. Photos later.