Saturday, March 9, 2013

Electric fan again

Well since it was about 35 yesterday, I decided to take the Valiant to pick the little one up from school. When it got to operating temperature, I just left the fan on. To further test it, I turned the air conditioning fan to full and the thermostat to the coldest setting. In stages of course since I didn't want the embarrassment of being stranded. It all worked really well, and I left the fan on a few minutes after stopping each time to prevent the usual heat build up, which all too often leads to an embarrassing blowing off of excess pressure (and water).
Also during Friday I visited the wrecker and got a nice looking volt meter from a Magna (well, it was probably put together in the same factory). Have to put it on yet, but it tested OK. Should then be able to tell if we ever get a case of over voltage or if the alternator just dies.

I also picked up a different thermostat: One I had a threaded nut for. Although I haven't faltered yet with turning the fan on and off, it'd be nice if it were taken care of automatically. This will be a job for next week.

Drive safely, preferably in an old Valiant, of course.

Monday, March 4, 2013

A few improvements

OK, last weekend was a big one for the Valiant. Several improvements made, and the car is better by far.

Electric fan

Pulled out the heavy one and put the electric fan in. Took ages (about 6 hours) and had to be offset, due to the water pump being in the way. Had to put another relay in since the fan draws a few amps. Did this first, and the ammeter went nuts every time I turned the fan on.

Bypassing the firewall plug

I did the improvement mentioned last post. A simple wire to connect the alternator with the starter relay. Now of course the ammeter doesn't work (sits at zero). I have to look out for a volt meter to replace it or turn the ammeter into a volt meter. I'm thinking the second option is preferred. It's more difficult since the thing will have to be calibrated but considering over-voltage killed my last battery it's essential to get one soon.


Linking the central locking to the alarm


Luckily (or it may be normal) the alarm has the ability to activate the central locking. Mine pulses a 400mA signal. The only way to get it working is to use two standard (bosch type) relays.
Here is how a relay is wired (taken from http://www.pbase.com/image/35092434.jpg):

The activation signal is (in my case) wired with a 12V wire at the other end. Activation signal from alarm to 87, battery to 30. This will allow the other two terminals to bridge. Other terminals are 86 to earth (a good one) and 87 to the central locking's "lock all" signal wire.
Do the same with the unlock.

Next plans

Put a relay in the headlight circuit, a bigger alternator and electronic regulator.

Thursday, February 28, 2013

Battery renewal

The Valiant's battery died a few weeks ago so I went and got another. This one is the heaviest duty one I could get, since the old one was only two years old.
The battery guy asked if the voltage regulator was OK, since over-voltage will do this sort of damage (acid everywhere, very low voltage, battery not charging). I shrugged and said "presume so. It's fairly new". It was also only a year or two old (probably less), but I got the old multimeter out and checked. Seems the guy just saved me another $160 (I stopped measuring when it got to 16.5V and turned the engine off). Buy one here and you will pay $125 (pentastar) to about $200. In America, you'll get a brand new one for about $2.95 but only if you live there. Those who sell to us charge about twice this. I landed one for a bit under $12, but it took two weeks. Now the Valiant is up and about again, and I have to wonder why the massive price difference. It's not the usual twice or three times as much like we're used to. We're charged over forty times what the Americans pay. No wonder the Internet is so popular. Unfortunately I missed the Ballarat swap meet because of the time taken (it arrived the day after).

When I was investigating the regulator, I found out that the Valiant's Ammeter is a major point of failure. No other car manufacturer threw 100% of generated current through the firewall (twice). This is bad, because as the car ages and the wires start to corrode, resistance increases. The physical effect of this is that the wire gets hotter. Frequently, the connectors melt (they are plastic) and everything short-circuits. It scared the bejesus out of me and I'll make conversion to a volt meter and re-routing of the alternator output. Here are some relevant references:
Replace your alternator and regulator with electronic variety
Explanation, and instructions on re-routing the wiring and replacing the ammeter

Monday, January 7, 2013

Hot weather and how to keep the old girl cool

When you have a classic car with A/C how do you keep it cool?

Here are some tips for keeping your car cool, from most easiest to less easiest ;-):

1. Clean your radiator, check your thermostat. I was amazed at how much rusty crap was blocking the radiator a few months ago. Clean it, as in take the radiator out of the car and tip it upside-down, hose it and buy some new concentrated anti-boil/anti-freeze. Also, very important to solder up any leaks or take it to get it fixed: Water leaks get worse due to the increase in pressure when it's hot. While you're at this, check your thermostat. If it works OK but your radiator isn't the best since they're all old and most have a few blockages, you can reduce the possibility of overheating by fitting a lower temperature thermostat. this makes the engine run slightly less efficiently, but I'd rather it use a little more fuel than break down at the first traffic jam. In Melbourne, very heavy traffic is a given and a nightmare for old cars.
2. Fit a better fan. The std fan for the Valiant 225 is a four blade. This is crap really, and at a recent (Bendigo, Nov 2012) swap meet I got a chromed hemi 6 bladed chromed fan (although the chrome has seen better days) for $10. This definitely made a big difference, but the car still overheats on really hot days (like last Saturday, 40°C). Bloody heavy fan but it pulls a lot more air through. It made a difference straight away, and the Val would definitely have failed on me before now if I hadn't done this.
3. Fit a shroud between the fan and the radiator, as close as possible to the fan. This forces more air to come from the front of the car into the radiator, rather than from around the engine bay. I modified a modern plastic one, pulled off a Volvo. Doesn't matter if you cut, glue, tape, screw etc. it together if you just want the effect.
4. Fit an electric fan. I bought one but haven't fitted it yet. It's the narrowest large diameter electric fan I could find ($60 ebay, sent from QLD) because the A/C compressor means there isn't much space. Electric fans have the advantage of efficiency: They don't operate when the water's cold and since it's not driven by the motor they don't take any effort to run (you get more horsepower and better fuel economy, and it gets better at higher engine speed like extractors). That said, they do require electricity, and when running, the alternator produces more drag on the engine. However, it's the best solution and the most difficult (I haven't done it yet). You'll need to completely remove the manual fan, of course, and possibly fit new screws (in case you need to put back the old fan which you should keep somewhere handy).
5. Check/renew your water pump. If your water pump is an older one or you have been a bit slack in putting the green inhibitor in the water it'll be corroded, and much less effective. It's easy to remove the pump and check this. If your pump is badly corroded, get a new one. I have a new one in the shed (hmm.. might start keeping it in the car - you never know) and they're not expensive or hard to find (auto surplus in Mitcham usually have them in stock, or even Repco). If your old one was corroded, you'll notice an immediate improvement.

Here are a few driving tips:
1. Is your car an automatic? If so, put it into neutral at the lights: Melbourne has the worst traffic and sitting at the lights is what overheats your car. Here's why: Your car idles slow in neutral, slower in drive, and it seems that although the faster idle creates more heat, the faster fan speed as well as the faster water pump more than makes up for this. I've tested it and in drive, my car overheats much faster than in neutral. If the traffic lights are known to take more than a minute to change, turn the engine off.
2. With aftermarket A/C you usually have a thermostat dial: When at the lights, turn it to warmer (less cold) and have the car in neutral. When not at the lights have it cooler.
The A/C heats your coolant up in two ways:
i. Dragging on the engine, slowing it down and creating more work for it.
ii. The condensor (at the front of the radiator) is the hot part of the heat exchanger, and heats up the air before it gets to the radiator (it sits in front of the radiator).

If your car is overheating, choose all or some of the following to slow or stop it (depending on the circumstances):
* Turn off the A/C.
* Stop the car. The water temperature will appear to go up rapidly when you do this and the radiator may blow out some water due to the pressure.
* Turn on the heater. This will provide additional cooling, albeit at the expense of comfort.

When you stop the car whilst overheating, it will probably blow some pressure in the form of water and/or steam. This is normal and nothing to worry about. If you're wanting to just put in some more water either wait for the engine to cool down (like, an hour) or throw a cloth over the radiator cap and remove it (note: It's really dangerous to remove the cap from a hot engine) then with the engine running pour in some water. If you don't have the engine running, the temperature difference once you start the engine may crack the block or head.

So to summarise:
* Flush your radiator by removing it

OK, that's Mike's tips for driving in the heat. I didn't drive the Val today: Took the missus' Verada instead (mmm... thermostatically controlled electric fan). Told you I hadn't installed the electric one yet: Might do so this week.
Mike

Tuesday, October 30, 2012

Unemployment really curbs the restoration

Well, not that I'm restoring the old girl, but having no money means that when (for example) the A/C lost its R134a (a few weeks ago - loose fitting at the evaporator), I can't even pay for a re-gas (yes, poor me, there there). Trying to convince oneself that the quarter vent open all the way is just as good will only work until Summer really hits :-( Probably have to do it anyway, considering my ten year old bundle of... well, something (love you sweetie, really).
This car will not be restored, ever. I love it as a daily driver and will continue to patch things up (properly) and drive it, and enjoy it.

Fuses

My attempt earlier in the year (April) to replace the original fuses with one from a Hyundai ended up with my throwing the new part away and investigating the old one. Although basic, it actually works very well until one of the fuses blows, which stops everything connected to it from working. I found out that my wipers and interior light were connected to the fused side. Here's how it works:
There is one power feed from the battery (always on) and one from the ignition (only one with the ignition). Keep a good supply of 15A fuses (a packet in the glove box), you have four options for any device you connect.
Do you want it fused or not? Do you need it on all the time. I'd recommend not putting the wipers on the fused end. For that matter the interior light shouldn't be fused either. If you have an alarm and the interior light doesn't work, neither will your alarm!
Definitely have the heater (and A/C if you have one) on the ignition side, and I have mine fused in case my stupidity or carelessness results in a short circuit (disconnection prior to working on the electrical system is advised here. Take note, me).
If you want extra safety, put in-line fuses on your devices. I've found it's so much easier to use the simple system Chrysler engineers put there.  Oh, and the diagram was just drawn by me: It won't necessarily look exactly like the fuse connector (which is more square and has a plastic cover). The fuse connector is located about halfway along your dash, and is secured with a screw. Remember that before taking a screwdriver near it, one part is connected directly to your battery!

Wednesday, August 22, 2012

Free Wheel Alignment for the old girl

A while ago I replaced the DS wishbone and ball joint. My Valiant guy's advice was to spray paint over the blah blah adjusters and I won't have to do a wheel alignment. After I replaced it, it was obvious I'd sprayed in the wrong place and so the wheel alignment was horribly out. The best thing I could do was to adjust the camber by eye for the driver's side (that's what DS is, incidentally) and take it to an alignment place later.
Alignment people said they could do a toe-in only alignment for $35 odd, but that a proper alignment would take a couple of hours at $85-$110 an hour! Needless to say I didn't take them up on it. About 6 weeks ago I happened to buy something off ebay for my daughter and picked it up where the guy worked (wheel and tyre place). He said he couldn't do an alignment until next week (it was about 15KM from home, so that was a no) but that it looked like a good job I'd done by eye.
Finally had enough of vague steering this morning and went to my Dad's place. He was a mechanic and is very good at improvisational car repair. He made up a camber tool with a spirit level and piece of angled aluminium, which he cut to the exact diameter of the rim. Placed the aluminium against the rim and the level against the aluminium (the aluminium piece was effectively an adaptor, needed because the level would be fouled by the tyre). The setup was made as vertical as possible and the bubble observed. What we should see was almost level but out very slightly at the top. I.E. \               /  
This is exaggerated of course. The angle should be about 0.5 of a degree.
Results? It seems I had the DS absolutely spot on, but surprisingly the PS (passenger side) was waaaaay out! Surprising since I hadn't touched it at all. It must have been like that for years. To fix it, I first of all measured the length in mm between the front and rear bolts and the panel on the inside. I moved it in by 3mm on both F and R, tightened the bolts, measured again, put the wheel back on (couldn't get at the bolts without removing the wheel) and moved the car back about 3m then forward (I don't trust the push down on the bonnet method of levelling). Measured with the level again and it was perfect. So, did a toe-in check, then correction, since adjusting the camber changed this then a test drive. Although it's not like power steering, it's noticeably lighter. Also, the steering is much more predictable than before which certainly makes me fell better about jumping in and taking my 10YO to school. Dad advised me to swap front and rear tyres (which I did), since the PS front is now looking a bit scrubbed thanks to running on the outside for so long.
Still a lot to do but at least she'll point straight and true :-)
Happy motoring!

P.S. The toe-in adjustment is very easy. You just need a steel measuring tape and (optionally) a piece of masking tape. With tyres facing perfectly forward, measure the distance between the two front tyres at the front-most part (that you can reach - the engine and chassis get in the way) then the rear-most part. The tyres should be 3mm (1/8") closer together at the front. If they aren't, adjust by loosening both parts of one side's tie rod ends and adjust. Tighten TREs, roll car back then forward about 3m and measure again. If you have a helper or really stiff measuring tape, you won't need the masking tape.

AC dead

Well, it seems the AC evaporator was dodgy. The fan started making noise about 6 months ago and I stupidly thought "Can't be anything wrong with it. It's brand new". Well, now I reckon it probably wasn't new (argh!) because the motor seized up and now it's just blowing fuses when I try and use it.

Well, all that trouble for nothing. Advice for anyone wanting A/C. Do it yourself or pay someone to do it. If you make a deal, get it clear and in writing.